View T645HW02-V1_5591847.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 1/30 2008 all rights reserved no reproduction and redistribution allowed product description: 65" full hd color tft-lcd module auo model name: t645hw02 v1 customer part no. / project name: customer signature au optronics corp. approved by: pm head / frank hsu reviewed by: rd head / hong-jye hong reviewed by: project leader / howard yeh prepared by: pm / child chiu note www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 2/30 2008 all rights reserved no reproduction and redistribution allowed rev.01 date: 2009/05/27 product functional specification 65" full hd color tft-lcd module model name: t645hw02 v1 (*) preliminary specification () final specification note: this specification is subject to change witho ut notice. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 3/30 2008 all rights reserved no reproduction and redistribution allowed contents no contents record of revisions 1 general description 2 absolute maximum ratings 3 electrical specification 3.1 signal electriacl characteristics 3.2 signal interface connector 3.3 signal timing specification 3.4 signal timing waveform 3.5 color input data reference 3.6 back light power specification 3.7 power sequence 4 optical specification 5 mechanical characteristics 6 packing 7 reliability test 8 international standard 9 precautions www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 4/30 2008 all rights reserved no reproduction and redistribution allowed record of revision rev. data page items new description remark 00 2009/05/05 -- first release n/a 01 2009/05/27 6 wet-bulb figure modify to correct figure 16 number of lamps modify to right number = 26 23-24 2d drawing modify to new version 27 vibration & shock test modify the condition www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 5/30 2008 all rights reserved no reproduction and redistribution allowed 1. general description this specification applies to the 65 inch color tft -lcd module t645hw02 v1. this lcd module has a tft active matrix type liquid crystal panel 1920x1080 p ixels, and diagonal size of 64.5 inch. this module supports full hd mode (non-interlace). each pixel is divided into red, green, and blue sub -pixels or dots which are arranged in vertical stri pes. gray scale or the brightness of the sub-pixel color is d etermined by 8-bit gray scale signal for each dot. the t645hw02 v1 has been designed to apply the 8-bi t 4-channel lvds interface method. it is intended t o support displays where high brightness, wide viewin g angle, double frame rate driving, and high color depth are important. the t645hw02 v1 is rohs verified which can be disti nguished on panel label. general information items specification unit note active screen size 64.53 inches diagonal display area 1428.48 (h) x 803.52 (v) mm outline dimension 1508.0(h) x 878.0(v) x 60.0(d) mm w/ inverter cover driver element a-si tft active matrix display colors 16.7m (8-bit) colors color gamut 72 % ntsc number of pixels 1920 x 1080 pixel pixel arrangement rgb vertical stripe pixel pitch 0.744 mm display mode transmissive, normally black surface treatment hclr, 3h total power consumption (380) watt include blu & signal life time (minimum) 50,000 hours [1] rohs rohs compliance note [1]: the life is determined as the time at whi ch luminance of the lamp is 50% compared to that of initial value at the typical lamp current on con dition of continuous operating at 252c. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 6/30 2008 all rights reserved no reproduction and redistribution allowed 2. absolute maximum ratings the followings are maximum values which, if exceede d, may cause faulty operation or damage to the unit : item symbol min. max unit note logic/lcd drive voltage v cc -0.3 +14.0 v [1] input voltage of signal v in -0.3 +3.6 v [1] blu input voltage v ddb -0.3 +27.0 v [1] blu brightness control voltage v blon -0.3 +7.0 v [1] operating temperature t op 0 +50 c [2] operating humidity h op 10 90 %rh [2] storage temperature t st -20 +60 c [2] storage humidity h st 10 90 %rh [2] panel surface temperature t sur -- +65 c [2] note [1]: if operate over spec but under absolute m aximum rating, duration must be < 50ms. note [2]: maximum wet-bulb should be 39c and no co ndensation. the relative humidity must not exceed 80% non-condensing at temperatures of 40c o r less. at temperatures greater than 40c, the wet bulb temperature must not exceed 39c . when operate at low temperatures, the brightness of ccfl will drop and the life time of ccfl will be reduced. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 7/30 2008 all rights reserved no reproduction and redistribution allowed 3. electrical specification the t645hw02 v1 requires two power inputs. one is e mployed to power the lcd electronics and to drive t he tft array and liquid crystal. the second input is t o power the inverter, which can power the ccfl. 3.1 signal electrical characteristics (ta = 25 2c) value parameter symbol min. typ. max unit note power supply input voltage v cc 10.8 12.0 13.2 v power supply input current i cc tbd a [2] power consumption p cc tbd watt [2] inrush current i rush -- -- tbd a [3] differential input high threshold voltage v th -- -- +100 mv [4] differential input low threshold voltage v tl -100 -- -- mv [4] lvds interface common input voltage v cim 1.10 1.25 1.40 v input high threshold voltage v ih (high) 2.4 -- 3.3 v cmos interface input low threshold voltage v il (low) 0 -- 0.7 v note: 1. the check pattern is base on white pattern. the rip ple voltage should be controlled under 10% of v cc . 2. v cc = 12.0v, f v = 60hz, f clk = 81.5mhz, 25c, v cc duration time = 470s, test pattern: full white pa ttern 3. measurement condition: rising time=470 s gnd vdd 0.1 vdd 0.9 vdd 400 s 470s www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 8/30 2008 all rights reserved no reproduction and redistribution allowed 4. measurement of lvds differential voltage is shown a s following: vth vcim vtl 0v 5. do not attach a conducting tape to lamp connecting wire. if the lamp wire attach to conducting tape, tft-lcd module has a low luminance and the inverter has abnormal action because leakage current occurs between lamp wire and conducting tape. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 9/30 2008 all rights reserved no reproduction and redistribution allowed 3.2 signal interface connections lcd lvds connector (41pin): jae fi-re41s-hf pin # signal name description note 1 v cc operating voltage supply, +12v dc regulated 2 v cc operating voltage supply, +12v dc regulated 3 v cc operating voltage supply, +12v dc regulated 4 v cc operating voltage supply, +12v dc regulated 5 v cc operating voltage supply, +12v dc regulated 6 gnd ground 7 gnd ground 8 gnd ground 9 gnd ground power 10 r1_0- lvds channel 1, signal 0- 11 r1_0+ lvds channel 1, signal 0+ 12 r1_1- lvds channel 1, signal 1- 13 r1_1+ lvds channel 1, signal 1+ 14 r1_2- lvds channel 1, signal 2- 15 r1_2+ lvds channel 1, signal 2+ 16 gnd ground 17 r1_clk- lvds channel 1, clock - 18 r1_clk+ lvds channel 1, clock + 19 gnd ground 20 r1_3- lvds channel 1, signal 3- 21 r1_3+ lvds channel 1, signal 3+ 22 r1_4- lvds channel 1, signal 4- 23 r1_4+ lvds channel 1, signal 4+ 24 gnd ground lvds channel 1 25 r3_0- lvds channel 3, signal 0- 26 r3_0+ lvds channel 3, signal 0+ 27 r3_1- lvds channel 3, signal 1- 28 r3_1+ lvds channel 3, signal 1+ 29 r3_2- lvds channel 3, signal 2- 30 r3_2+ lvds channel 3, signal 2+ 31 gnd ground 32 r3_clk- lvds channel 3, clock - 33 r3_clk+ lvds channel 3, clock + 34 gnd ground lvds channel 3 www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 10/30 2008 all rights reserved no reproduction and redistribution allowed pin # signal name description note 35 r3_3- lvds channel 3, signal 3- 36 r3_3+ lvds channel 3, signal 3+ 37 r3_4- lvds channel 3, signal 4- 38 r3_4+ lvds channel 3, signal 4+ 39 gnd ground lvds channel 3 40 nc no connect (auo internal use only) 41 nc no connect (auo internal use only) lcd lvds connector (51pin): jae fi-re51s-hf pin # signal name description note 1 v cc operating voltage supply, +12v dc regulated 2 v cc operating voltage supply, +12v dc regulated 3 v cc operating voltage supply, +12v dc regulated 4 v cc operating voltage supply, +12v dc regulated 5 v cc operating voltage supply, +12v dc regulated 6 gnd ground 7 gnd ground 8 gnd ground 9 gnd ground power 10 r2_0- lvds channel 2, signal 0- 11 r2_0+ lvds channel 2, signal 0+ 12 r2_1- lvds channel 2, signal 1- 13 r2_1+ lvds channel 2, signal 1+ 14 r2_2- lvds channel 2, signal 2- 15 r2_2+ lvds channel 2, signal 2+ 16 gnd ground 17 r2_clk- lvds channel 2, clock - 18 r2_clk+ lvds channel 2, clock + 19 gnd ground 20 r2_3- lvds channel 2, signal 3- 21 r2_3+ lvds channel 2, signal 3+ 22 r2_4- lvds channel 2, signal 4- 23 r2_4+ lvds channel 2, signal 4+ 24 gnd ground lvds channel 2 www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 11/30 2008 all rights reserved no reproduction and redistribution allowed pin # signal name description note 25 r4_0- lvds channel 4, signal 0- 26 r4_0+ lvds channel 4, signal 0+ 27 r4_1- lvds channel 4, signal 1- 28 r4_1+ lvds channel 4, signal 1+ 29 r4_2- lvds channel 4, signal 2- 30 r4_2+ lvds channel 4, signal 2+ 31 gnd ground 32 r4_clk- lvds channel 4, clock - 33 r4_clk+ lvds channel 4, clock + 34 gnd ground 35 r4_3- lvds channel 4, signal 3- 36 r4_3+ lvds channel 4, signal 3+ 37 r4_4- lvds channel 4, signal 4- 38 r4_4+ lvds channel 4, signal 4+ 39 gnd ground lvds channel 4 40 nc no connect (auo internal use only) 41 nc no connect (auo internal use only) 42 nc no connect (auo internal use only) 43 nc no connect (auo internal use only) 44 nc no connect (auo internal use only) 45 lvds_sel open/high(3.3v) for ns, low(gnd) for je ida default: ns 46 nc no connect (auo internal use only) 47 nc no connect (auo internal use only) 48 nc no connect (auo internal use only) 49 nc no connect (auo internal use only) 50 nc no connect (auo internal use only) 51 nc no connect (auo internal use only) note [1]: all gnd (ground) pins should be connected together and should also be connected to the lcd?s metal frame. note [2]: all v cc (power input) pins should be connected together. note [3]: all nc (no connection) pins should be ope n without voltage input. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 12/30 2008 all rights reserved no reproduction and redistribution allowed lvds option = open/high(3.3v) ns rx_clk+ rx_clk- rx_0+ rx_0- rx_1+ rx_1- rx_2+ rx_2- rx_3+ rx_3- rx_4+ rx_4- (x = 1~4) g0 r5 r4 r3 r2 r1 r0 r0 g0 b1 b0 g5 g4 g3 g2 g1 g1 b1 de vs hs b5 b4 b3 b2 b2 de na b7 b6 g7 g6 r7 r6 r6 na na b9 b8 g9 g8 r9 r8 r8 na current cycle next cycle previous cycle lvds option = low(gnd) jeida rx_clk+ rx_clk- rx_0+ rx_0- rx_1+ rx_1- rx_2+ rx_2- rx_3+ rx_3- rx_4+ rx_4- (x = 1~4) g4 r9 r8 r7 r6 r5 r4 r4 g4 b5 b4 g9 g8 g7 g6 g5 g5 b5 de vs hs b9 b8 b7 b6 b6 de na b3 b2 g3 g2 r3 r2 r2 na na b1 b0 g1 g0 r1 r0 r0 na current cycle next cycle previous cycle www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 13/30 2008 all rights reserved no reproduction and redistribution allowed 3.3 signal timing specification this is the signal timing required at the input of the user connector. all of the interface signal timi ng should be satisfied with the following specifications for its proper operation. timing table (de only mode) vertical frequency range (120hz) signal item symbol min. typ. max unit period t v 1096 1130 1160 t h active t disp (v) 1080 vertical section blanking t blk (v) 16 50 80 t h period t h 560 570 580 t clk active t disp (h) 480 horizontal section blanking t blk (h) 80 90 100 t clk period t clk 13.58 12.94 12.39 ns clock frequency f clk 73.65 77.29 80.74 mhz vertical frequency frequency f v 118 120 122 hz horizontal frequency frequency f h 131.52 135.6 139.2 khz www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 14/30 2008 all rights reserved no reproduction and redistribution allowed 3.4 signal timing waveform www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 15/30 2008 all rights reserved no reproduction and redistribution allowed 3.5 color input data reference the brightness of each primary color (red, green, and blue) is based on the 8-bit gray scale data input f or the color; the higher the binary input, the brighter the color. the table below provides a reference for color v ersus data input. color data reference input color data red msb lsb green msb lsb blue msb lsb color r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 basic color white 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 red(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ---- red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 ---- green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 green green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 blue(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ------- blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 blue blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 16/30 2008 all rights reserved no reproduction and redistribution allowed 3.6 backlight power specification electrical specification (ta=255 o c, turn-on after 60mins) specification item symbol min. typ. max unit note 1 high voltage (hv) input hv1/ hv2 tbd tbd tbd v rms 2 input current of ech hv i hv tbd tbd tbd ma rms 3 high voltage (hv) output v out tbd tbd tbd v rms 4 output lamp current i out 8.0 8.5 9.0 ma rms pwm=100% 5 operating frequency f op 43 45 47 khz (recommend) 6 pwm dimming frequency f pwm 140 180 240 hz (recommend) 7 dimming duty ratio d pwm 30 100 % (recommend) 8 lamp type straight 9 number of lamps 26 pcs protection circuit (feedback signal): 10 supply voltage v cc - tbd - v dc 11 supply current i cc tbd ma dc 12 current feedback signal v fb tbd v rms v ld (h) vcc-0.5 vcc v dc lamp normal status 13 lamp detection (olp) v ld (l) 0.8 v dc lamp protection status lamp specification: 14 output working voltage v l tbd tbd tbd v rms i l =6.0ma rms 15 output current i l 8.0 8.5 9.0 ma rms 16 lamp frequency f lamp 43 45 47 khz 17 starting voltage vs _ _ _ v rms ta=25 o c( spc. ) www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 17/30 2008 all rights reserved no reproduction and redistribution allowed inverter interface connection cn1: civilux_ci0114m1hrl-nh pin # symbol description 1 v ddb operating voltage supply, +24v dc regulated 2 v ddb operating voltage supply, +24v dc regulated 3 v ddb operating voltage supply, +24v dc regulated 4 v ddb operating voltage supply, +24v dc regulated 5 v ddb operating voltage supply, +24v dc regulated 6 gnd ground 7 gnd ground 8 gnd ground 9 gnd ground 10 gnd ground 11 det normal display: ( (( (Q QQ Q0.8v) 0.8v) 0.8v) 0.8v) , fail: open collector 12 vblon bl on-off: high (3.3~5v) for bl on , low/open (gnd) for off 13 internal pwm(vdim) internal pwm dimming high (3.3v/100% duty) for 100% lum; 14 external pwm(pdim) external pwm dimming (30%~100% duty) ; note (1) det is output pin for detect power error. when backlight is normal operation, det is gnd(0v). when backlight is abnormal, det is high(5v). note (2) pwm dimming function is included internal pwm and external pwm. internal pwm: input voltage 0 (gnd) ~3.3v to pin 13 th, and duty ratio of output voltage/current of inverter is from 30% to 100%. when use pin 13th to control backlight luminance, the pin 14th will be nc and can not be affect by noise! external pwm: input duty ratio 30% ~100% to pin 14th, and duty ratio of output voltag e/current of inverter is from 30% to 100%. when use pin 14th to control backlight luminance, the pin 13th will be nc and can not be affect by noise! pin 13th and pin 14th can not be used at the same time! www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 18/30 2008 all rights reserved no reproduction and redistribution allowed cn2: civilux_ci0114m1hrl-nh pin # symbol description 1 v ddb operating voltage supply, +24v dc regulated 2 v ddb operating voltage supply, +24v dc regulated 3 v ddb operating voltage supply, +24v dc regulated 4 v ddb operating voltage supply, +24v dc regulated 5 v ddb operating voltage supply, +24v dc regulated 6 gnd ground 7 gnd ground 8 gnd ground 9 gnd ground 10 gnd ground 11 nc no connect 12 nc no connect 13 nc no connect 14 nc no connect note [3]: all gnd (ground) pins for all 4 connectors should be connected together and should also be connected to the lcd?s metal frame. note [4]: all v ddb (power input) pins for all 4 connectors should be connected together. note [5]: all nc (no connection) pins should be open without voltage input. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 19/30 2008 all rights reserved no reproduction and redistribution allowed 3.7 power sequence power sequence of lcd 10% 90% 90% 10% t1 t2 t3 t4 t5 t6 t7 lamp on valid data power supply for lcd signal backlight values parameter min. typ. max. unit t1 0.4 -- 30 ms t2 0.1 -- 50 ms t3 300 -- -- ms t4 10 -- -- ms t5 0.1 -- 50 ms t6 -- -- 300 ms t7 500 -- -- ms apply the lamp voltage within the lcd operating range. when the backlight turns on before the lcd operati on or the lcd turns off before the backlight turns off, the display may momentarily become abnormal. caution: the above on/off sequence should be applied to avoid abnormal function in the dis play. in case of handling, make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 20/30 2008 all rights reserved no reproduction and redistribution allowed power sequence of inverter values parameter min. typ. max. unit t1 20 -- -- ms t2 500 -- -- ms t3 250 -- -- ms t4 0 -- -- ms t5 1 -- 50 ms t6 -- -- 10 ms www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 21/30 2008 all rights reserved no reproduction and redistribution allowed 4. optical specification optical characteristics are determined after the unit has been ?on? and stable for appr oximately 60 minutes in a dark environment at 25c. the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0. test condition: (ta=255 o c, turn-on after 60mins) values parameter symbol min. typ. max unit notes contrast ratio cr 4000 5000 -- [1], [2] surface luminance (white) l wh 400 500 -- cd/m 2 [1], [3] luminance variation white(9p) -- -- 1.3 [4] response time (average) t r -- 5.5 -- ms [1],[5] (gray to gray) color coordinates (cie 1931) red r x 0.64 [1] r y 0.33 [1] green g x 0.29 [1] g y 0.60 [1] blue b x 0.15 [1] b y 0.06 [1] white w x 0.28 [1] w y typ.-0.03 0.29 typ.+0.03 [1] viewing angle (contrast ratio>10) x axis, right( =0) r -- 89 -- degree [1], [6] x axis, left( =180) l -- 89 -- degree [1], [6] y axis, up( =90) u -- 89 -- degree [1], [6] y axis, down ( =270) d -- 89 -- degree [1], [6] www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 22/30 2008 all rights reserved no reproduction and redistribution allowed note [1]: the values of contrast ratio, surface luminance, response time, color coordinates, and viewing angl e are measured at center point of display area. note [2]: contrast ratio (cr) is defined mathematically as: note [3]: surface luminance is luminance value at center point of display area, 50cm from the surface wi th all pixels displaying white. note [4]: the variation in surface luminance, white(9p) is defined as: white(9p) = maximum(l on1 , l on2 ,?,l on9 )/minimum(l on1 , l on2 ,?l on9 ) note [5]: response time tr is the average time required for display transition by switching the input s ignal for five luminance ratio (0%, 25%, 50%, 75%, 100% brightness matrix) and is based on f v = 60hz to optimize. contrast ratio (cr) = brightness of 'full white' state brightness of 'full black' state 1 2 3 4 5 6 7 8 v h v/6 v/2 h/2 h/6 9 www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 23/30 2008 all rights reserved no reproduction and redistribution allowed note [6]: viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determined for the horizontal (or x-axis) and the vertical (or y-axis) with respect to the z-axis which is normal to the lcd surface. 5. mechanical characteristics the contents provide general mechanical characteristics for the model t645hw01 v0. detailed mechanical drawings are shown in the following pages. horizontal (typ.) 1508.0 mm vertical (typ.) 878.0 mm outline dimension depth (typ.) 60.0 mm (with inverter) horizontal (typ.) 1440.6 mm bezel opening area vertical (typ.) 814.6 mm horizontal 1428.48 mm active display area vertical 803.52 mm weight 33 kg (max) www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 24/30 2008 all rights reserved no reproduction and redistribution allowed 2d drawing (front) - draft www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 25/30 2008 all rights reserved no reproduction and redistribution allowed 2d drawing (rear) - draft www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 26/30 2008 all rights reserved no reproduction and redistribution allowed 6. packing a. panel label b. carton label c. packing instruction d. packing specification [ packing information will be updated in next speci fication revision. ] www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 27/30 2008 all rights reserved no reproduction and redistribution allowed 7. reliability test no test item q'ty condition 1 high temperature storage 3 pcs ta = 60c, 300hr judge 2 low temperature storage 3 pcs ta = -20c, 300hr judge 3 high temperature operation 3 pcs ta = 50c, 300hr judge 4 low temperature operation 3 pcs ta = -5c , 300hr judge 5 vibration test [note] (non-operating) 3 pcs waveform: random vibration level: 1.5g rms bandwidth:10-300hz duration: 30min in each x, y, z direction 6 shock test [note] (non-operating) 3 pcs shock level: 30 g waveform: sine wave, 11ms direction: x, y, z one time each direction 7 vibration test (with carton) 1 box waveform: random vibration level: 0.83g rms bandwidth:10-200hz duration: 30min in each x, y, z direction 8 drop test (with carton) 1 box height: 31cm 1 corner, 3 edges, 6 surfaces (astmd5276 note. need to confirm the test criteria for ultra size panel with customer. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 28/30 2008 all rights reserved no reproduction and redistribution allowed 8. international standard 8.1 safety (1) ul1950 third edition, underwriters laboratories, inc. jan 28, 1995 standard for safety of information technology equipment including electrical business equipment (2) can/csa c22.2 no. 950-95 third edition, canadian standards association standard for safety of information technology equipment including electrical business equipment (3) en60950: 1992+a2: 1993+a2: 1993+c3: 1995+a4: 1997+a11: 1997 iec 950: 1991+a1: 1992+a2: 1993+c3: 1995+a4:1996 european committee for electrotechnical standardization (cenelec) european standard for safety of information technology equipment including electrical busines s equipment 8.2 emc (1) ansi c63.4 ?methods of measurement of radio-noise emissions from low-voltage electrical a nd electrical equipment in the range of 9khz to 40ghz. ?american national standards institute(ansi), 1992 (2) c.i.s.p.r ?limits and methods of measurement of radio interface characteristics of information technology equipment.? international special committee on radio interference. (3) en 55022 ?limits and methods of measurement of radio interface characteristics of information technology equipment.? european committee for electrotechnical standardization. (cenelec), 1998 www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 29/30 2008 all rights reserved no reproduction and redistribution allowed 9. precautions please pay attention to the followings when you use this tft lcd module. 9.1 mounting precautions (1) you must mount a module using holes arranged on back or edge side of panel. (2) you should consider the mounting structure so that uneven force (ex. twisted stress) is not appl ied to module. and the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protective plate to the surface in order to protect the polarizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for the cover case are not desirable because the for mer generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than h b pencil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front/rear polarizer. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possible. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. (10) due to heavy weight, please do not handle the panel by human without proper tooling for safety consideration. 9.2 operating precautions (1) the device listed in this product specification sheets was designed and manufactured for tv applic ation. (2) the spike noise causes the mis-operation of circuits. it should be lower than following voltage: v=200mv (over and under shoot voltage) (3) response time depends on the temperature. (in lower temperature, it becomes longer.) (4) brightness of ccfl depends on the temperature. (in lower temperature, it becomes lower.) and in low er temperature, response time (required time that brightness is stable after turned on) becomes longer. (5) be careful for condensation at sudden temperature change. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (6) when fixed patterns are displayed for a long time, remnant image is likely to occur. www..net
model name: t645hw02 v1 product specification (preliminary) ?copyright au optronics corp. rev.01 page 30/30 2008 all rights reserved no reproduction and redistribution allowed (7) module has high frequency circuits. sufficient suppression to the electromagnetic interference s hall be done by system manufacturers. grounding and shielding methods may be important to minimize the interface. 9.3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground through wrist band etc. and don?t touch interface pin directly. 9.4 precautions for strong light exposure strong light exposure causes degradation of polarizer and color filter. 9.5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunlight or fluorescent light. keep the temperature between 5c and 35c at normal humidity. (2) the polarizer surface should not come in contact with any other object. it is recommended that they be stored in the container in which they were shipped. 9.6 handling precautions for protection film (1) the protection film is attached to the bezel with a small masking tape. when the protection film is peeled off, static electricity is generated between the film and polarizer. this should be peeled off slowl y and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) when the module with protection film attached is stored for a long time, sometimes there remains a very small amount of flue still on the bezel after the protection film is peeled off. (3) you can remove the glue easily. when the glue remains on the bezel or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked w ith normal-hexane. www..net

▲Up To Search▲

Price & Availability of T645HW02-V1

	To Download T645HW02-V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .